Current Setup
This is my DJ Setup that i am trying to optimize for any and all use's.
One set is SP2A Precision Transduceor:
Max Power 300 W RMS (Program)
150W RMS (34.6V RMS Cont)
Independance: 8 Ohms
Xover: 800 Hz
Other set is
SP2TI Sound Renforcement System
Max 600W RMS (Program)
300W RMS (49V RMS Cont)
Indepence: 8 Ohms
Xover: 800 Hz
I Have 2 set's of both. Current way of using is the SP2 TI on bottom using only the Low input using it like a sub, the SP2A is Bi-Amped normal.
The amps i am using are as follows:
Samson Servo 550 175 watts into 8 ohms for horn's only
AB Interntional 900A 590 watts into 4 ohms per side side A for Mid's and side B for Low's.
Current setting for my Driverack PA is as follow's and this is where my questions are. The Crossover settings are from Peavey's help that i have gotten as well as some basic info on the PEQ. The stuff i still don't know about is how to properly use the crossover.
Here is my setting please correct if you think they should be changed...
GEQ i usually will pink the room and let it eq for me cept for the following i was told to use from Peavey cause they have CD horn's 2K Thru 4K -10/ 5K -4/ 6.3K -2/8K Zero/ 10K +2/ 12.5K +4/ 16K +6
PEQ Peavey Also gave me this advice too: LH Shelf 4.5K/ -10dB/ Q 0.20 - 1.60K/-10dB/Q12.4
Sub Harmonic's are off
Crossover is set as following, Basic info Peavey Provided to maxamize the speakers operating range:
High's: 1.60Khz/ LR12 (Is that the same as 2nd order?)/ 0dB
Mid's: 1.60Khz/ LR 24 (Is that the same as 4th order?)
125Hz/ LR24/ 0dB
Low's: 125Hz/ LR24
40Hz/ LR24/ 0dB
AFS at 6 notches
Compressor Also i need help here not sure if i have this set right.
L&R Combined, Threshold -10/ 2.0:1/ Gain 0/ Overeasy 10
Limiter: High's Overeasy 10/ -10 Gain
Mid's Overeasy 10/ -7 Gain
Low's Overeasy 10/ +10 Gain
No Delay
I love the way it sounds like this if there is any questions about any thing here let me know. I gave as much info as i could that i know.
Spynn
One set is SP2A Precision Transduceor:
Max Power 300 W RMS (Program)
150W RMS (34.6V RMS Cont)
Independance: 8 Ohms
Xover: 800 Hz
Other set is
SP2TI Sound Renforcement System
Max 600W RMS (Program)
300W RMS (49V RMS Cont)
Indepence: 8 Ohms
Xover: 800 Hz
I Have 2 set's of both. Current way of using is the SP2 TI on bottom using only the Low input using it like a sub, the SP2A is Bi-Amped normal.
The amps i am using are as follows:
Samson Servo 550 175 watts into 8 ohms for horn's only
AB Interntional 900A 590 watts into 4 ohms per side side A for Mid's and side B for Low's.
Current setting for my Driverack PA is as follow's and this is where my questions are. The Crossover settings are from Peavey's help that i have gotten as well as some basic info on the PEQ. The stuff i still don't know about is how to properly use the crossover.
Here is my setting please correct if you think they should be changed...
GEQ i usually will pink the room and let it eq for me cept for the following i was told to use from Peavey cause they have CD horn's 2K Thru 4K -10/ 5K -4/ 6.3K -2/8K Zero/ 10K +2/ 12.5K +4/ 16K +6
PEQ Peavey Also gave me this advice too: LH Shelf 4.5K/ -10dB/ Q 0.20 - 1.60K/-10dB/Q12.4
Sub Harmonic's are off
Crossover is set as following, Basic info Peavey Provided to maxamize the speakers operating range:
High's: 1.60Khz/ LR12 (Is that the same as 2nd order?)/ 0dB
Mid's: 1.60Khz/ LR 24 (Is that the same as 4th order?)
125Hz/ LR24/ 0dB
Low's: 125Hz/ LR24
40Hz/ LR24/ 0dB
AFS at 6 notches
Compressor Also i need help here not sure if i have this set right.
L&R Combined, Threshold -10/ 2.0:1/ Gain 0/ Overeasy 10
Limiter: High's Overeasy 10/ -10 Gain
Mid's Overeasy 10/ -7 Gain
Low's Overeasy 10/ +10 Gain
No Delay
I love the way it sounds like this if there is any questions about any thing here let me know. I gave as much info as i could that i know.
Spynn
Comments
Gadget
DRA