NXB-CCG Netlinx Clear Connect Gateway

JohnMichnr
JohnMichnr Junior Member
in AMX Hardware
I don't have one of tehse boxes in front of me yet, and am trying to prep for them. Does anybody know how these boxes connect to the master? Going through the manual and the module it looks like they are just IP appliances not ICSLan boxes. So I assume I'll have to manage the online/offline connectivity of them.

Has anybody worked with them before (and not used the module)
· Share on FacebookShare on Twitter

Comments

  • John Nagy
    John Nagy CineTouch Product Manager
    Unlike any "NXB" device I've seen before, these are apparently not native NetLinx devices, just as you deduced. The interface even suggests that the box could be used with other than AMX integrations. You might look at the Module that's offered on the product page, it may give more clues as to connection method... but IP client looks like the answer. Some of the more ambiguous doc I've read in a while.
    · Share on FacebookShare on Twitter
  • JohnMichnr
    JohnMichnr Junior Member
    John Nagy wrote: »
    Some of the more ambiguous doc I've read in a while.

    My thoughts exactly. The module doc just shows the device defined at 0:3:0. That is the only real clue that I've found so far.

    I wish I knew weather it would stay connected once connected, or if I'm going to have to constantly open and close the port for polling.
    · Share on FacebookShare on Twitter
  • DHawthorne
    DHawthorne Junior Member
    AMX has always been weak with documentation. They need to hire more technical writers. Most of their modules just give you a list of commands (which may or may not be complete), a list of responses (which may or may not be complete), and an example program. No mention of which elements are needed in what circumstances, or how to properly implement it on a scaled basis. It drives me nuts.
    · Share on FacebookShare on Twitter
  • JohnMichnr
    JohnMichnr Junior Member
    So often, if you know how the piece works, and how to program it, the documentation makes perfect sense. But then you don't need to read the documentation.

    I find that really true with the RMS stuff.
    · Share on FacebookShare on Twitter
  • PhreaK
    PhreaK Senior Member
    JohnMichnr wrote: »
    I find that really true with the RMS stuff.
    Ditto. Also x1000 with Duet.
    · Share on FacebookShare on Twitter
  • troberts
    troberts Member
    Can anyone tell me if the dimmers connected to the NXB-CCG be controlled with the exact same protocol as Lutron RA2? Specifically #OUTPUT commands?
    Then the age old question, do spend time writing code to talk to the AMX module or do I write my own? Any input would be appreciated.
    .
    .
    "Opps* guess I didnt scroll down far enough in the manual the first time. I see it does support #OUTPUT commands. Now just for the "age old question"
    · Share on FacebookShare on Twitter
  • TonyAngelo
    TonyAngelo Code Monkey
    JohnMichnr wrote: »
    My thoughts exactly. The module doc just shows the device defined at 0:3:0. That is the only real clue that I've found so far.

    I wish I knew weather it would stay connected once connected, or if I'm going to have to constantly open and close the port for polling.

    Because it's not an AMX device. It's a Lutron device.
    · Share on FacebookShare on Twitter
  • ericmedley
    ericmedley Senior Member - 3709 Posts
    I did a system with a couple gateways. It works okay. A little slow but works as described.
    · Share on FacebookShare on Twitter
  • felixmoldovan
    felixmoldovan Junior Member
    Reviving this thread for a complementary question. Is the NXB-CCG compatible with the rebadged devices only or will it work with the Lutron devices too? Is there anything different between the two?
    i.e. would MRF2-600M work or only the AMX CCD-6D?
    Similarly with the counterpart occupancy sensor LRF2-OCRB2-P-WH vs the AMX CCD-OCRB-P.
    · Share on FacebookShare on Twitter
  • ericmedley
    ericmedley Senior Member - 3709 Posts
    from the AMX Product webpage
    FEATURES


    •Clear Connect Enabled – Lutron's patented RF Technology uses a quiet band, essentially free of interference ensuring reliable communication between system devices
    •Perfect Way to Add Light Control – Easily integrates with existing electrical infrastructures – simply replace the light switch
    •Create Light & Control Events with Room Occupancy – Use the Clear Connect Wireless Occupancy Sensor with RMS to automatically power-up and shut-down the lights and AV equipment to maximize energy conservation
    •Simple Web Configuration – Browse to the NetLinx Clear Connect Gateway URL to quickly configure and program Clear Connect Enabled Switches, Dimmers, Keypads and Occupancy/Vacancy Sensors
    · Share on FacebookShare on Twitter
  • gloomy goose
    gloomy goose Junior Member
    Only RadioRa2 line is supported.
    · Share on FacebookShare on Twitter

Leave a Comment

BoldItalicStrikethroughOrdered listUnordered list
Format
SpoilerCodeQuote
Heading 2Heading 1
Emoji
:):D:(;):/:o:s:p:'(:|B):#:*<3o:)>:)
Url
Image
Align leftAlign centerAlign rightToggle HTML viewToggle full pageToggle lights
Drop image/file
Comment As ...

Categories